* ASatLogger TNC configuration file D7GO32INIT.TNC  Configure D7 for operations with GO-32 Satellite.

*NOTICE!!!!!!!
*  The contents of TNC configuration files may not be suitable for your TNC or radio.
*  The user must edit TNC configuration files to suit his intended purpose before 
*  initializing the TNC. The author assumes no responsibility for misconfigured 
*  TNC's / radios  or improper operation of same. Please refer to your TNC or radio 
*  manual to determine the  commands needed by your TNC / radio  before editing
*  ASatLogger TNC configuration files and  before sending the files to your TNC or radio.

* Comments begin with * or #.  Empty (blank) lines or lines starting with these char will not be sent to the TNC.
* Lines beginning with & are ASatLogger remote commands
* Control characters can be entered as ^M for example.

* TNC configuration files can be edited and saved in ASatLogger and sent to an attached TNC/Radio.
* TNC files can contain TNC commands, D7* radio commands, Text to transmit in converse mode and
* ASatLogger "remote commands".  See "Remote command help" for details.

* Force TNC into command mode
^C^C^C

#Force TNC OFF when programming radio.  The command &SENDTNCFFG D7MODECTRL.TNC could be used here as well.
TC 1

# D7 radio commands follow (Remove asterisk to enable commands in this file):
# Turn on Auto Information function (0=OFF 1=ON).  
AI 1

# Change VFO/Memory mode (band,Mode) bandA=0 BandB=1, VFO= 0, Memory= 2
# force A and B into VFO mode
VMC 0,0
VMC 1,0

# Select VFO VFOa = BC 0, VFOb=BC 1
BC 0

# Set frequency (freq,band). 0=vhf, 1= UHF
# Band A 
FQ 00145930000,0
#Band B
FQ 00435225000,1

# Set the freq step (0=5,1=6.25,2=10,3=12.5,4=15,5=20,6=25,7=30,8=50,9-100
ST 0
# Change step from Serial port tab by sending DW to move down 1 step, UP to move up 1 step.
# When in VFO mode, moves freq step, when in Memory mode, moves channel.

# Set Data band (0=band A,1=Band B,2=Band A tx Band B RX, 3=Band B tx, Band A Rx)
DTB 2

#Set Offset.  Simplex=0, Pos offset=1, Neg offset=2
SFT 0

# Force TNC to transmit 9600 when in APRS Mode 0=1200, 1=9600
PKSA 1

# Set DCD Sense (0=ignore, 1 = data or TX band, 2 = both bands).
DS 0

# Set APRS beacon mode (0=manual, 1= PTT, 2 = Auto).
DTX 2

# Set Duplex Mode (0=simplex, 1 = duplex)
DUP 0

# Set position comment (0=off duty,1=Enroute,2=inservice,3=Returning,4=Committed,5=Special,6=Priorty,7-13= custom0-6,14=Emergency
POSC 5

# Set Packet beacon TX 0=manual, 1=PTT, 2 = auto
DTX 0

# TX interval  0=.2 minutes, 1=0.5min, 2=1min, 3= 2min, 4 = 3min 5= 5 min 6= 10, 7=20, 8=30
TXI 3

# Set GPS mode (0=none,1=NMEA,2=NMEA9600)  Note:  NMEA= 4800
GU 1

# Set ICON (Graphical internal D7 ICONS 0-9 or A-E,Or submitted ICONS.
*ICO 0,2
#Alternately, select any APRS icon.  Satellite gateway
ICO 1,S&

#Tnc Txdelay = TXD * 10 milliseconds
TXD 30

# Set UNPROTO text  (Destination call)
UPR APK001

# Set Packet path (vias)
PP 4XTECH

# Set autoreply message OFF.  0=off,1=on
AMR 0

# BLN group 
*ABLG All CQ 

#MSG group
*AMGG *

# Send a message (Memory, Destination call, msg text
*AMSG 00,KC9XG,Using ASatLogger.

# Put in FM mode, 0=FM, 1=AM
*MD 0

# Set band A to high power 
PC 0,0

# Set Date YYMMDD

# Set Time zone ref UTC: 0=-12,hrs,1=-11.5hrs,2=-11,3=10.5hrs (every 30 minutes up to 24), 24=UTC, 25=UTC + 30min etc
# Set to UTC
TZ 24

AI 0

# Reset TNC to Packet mode. 
TC 0

# Turns TNC off when in Packet or APRS mode
*TC 1

# Use the remote command Delay to give radio time to switch to pkt mode
&DELAY 2

# TNC mode, 0 = off, 1 = APRS 2 = packet.  
*TNC 0
*TNC 1
*TNC 2

# Once TNC mode has been switched, set HBAUD.  The remote command &SETHBAUD could be used as well.
HBAUD 9600

# Now do some TNC settings to ensure it works with ASatLogger.
AWlen 8
BBSMsgs OFF
B E 0
Echo on
FLow off
AUTOLF off
MCOM off
MON ON
MRPt on
PACLen 0
PASSALL OFF